ASTM D4066 PDF

Buy ASTM D CLASSIFICATION SYSTEM FOR NYLON INJECTION AND EXTRUSION MATERIALS (PA) from SAI Global. ASTM D Standard Classification System for Nylon Injection and Extrusion Materials (PA). standard by ASTM International, 07/01/ View all product. 暂无评价|0人阅读|0次下载 | 举报文档. D – 01A Nylon Injection and Extrusion Materials_能源/化工_工程科技_专业资料。ASTM D标准.

Author: Nelkis Shakagore
Country: Montenegro
Language: English (Spanish)
Genre: Video
Published (Last): 11 September 2005
Pages: 394
PDF File Size: 6.91 Mb
ePub File Size: 18.44 Mb
ISBN: 142-9-83269-974-4
Downloads: 43386
Price: Free* [*Free Regsitration Required]
Uploader: Kijar

It is the responsibility of the user of this atsm to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Link to Active This link will always route to astj current Active version of the standard. O Group 07 nylons are presently used commercially only as reinforced materials. NOTE 8—Ash content of?

An example of an unreinforced nylon material is given as follows: If no properties are speci? NOTE 9—An ashm of this classi? All other grades are listed by requirements. Seven laboratories, including 3 U. L Izod impact requirements for Group 04 materials based on specimens with a Active view current version of standard. Testing Conditions ISO Note 2 — This classification system is being revised to include international 4-mm specimens and test procedures as the standard for compliance.

  CSHARP COMO PROGRAMAR DEITEL PDF

D If a speci?

H Requirements are based on unannealed test specimens 3. D Practice for Sampling of Plastics. It is recommended that the material manufacturer be consulted on all call-outs against this classification system. Your comments are invited either for revision of this standard or for additional standards and should be d066 to ASTM International Headquarters. NOTE 6—Materials containing reinforcements or? These may be speci?

Nylon 6 Supplier | Type 6/6 Nylon | Nylon Sheet

Current edition approved Qstm 10, D — G Izod impact for these materials shall be conducted aetm specimens with a It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Suffix values will override the PA table values. This standard does not purport to address all of the safety concerns, if any, associated with its use.

Selection of process temperature is made based on the major polymer component. The designation PAG35 indicates the following: This section may also include descriptions of the changes or reasons for the changes, or both.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. These will be asym out in detail and identi? General Principles ISO The reinforcement letter designations and associated tolerance levels are shown as follows: Electrodes shall be American Standard No.

  CALCULO DIFERENCIAL E INTEGRAL JAMES STEWART 2DA EDICION PDF

There may be other requirements necessary to identify particular characteristics important to specialized applications. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Industrial & Engineering Plastics

R Tensile strength and elongation shall be determined on Test Method D test specimens 3. Link to Active This link will always route to the current Active version of the standard. Viscosities for Groups 03, 04, 06, and 08 are measured as described as follows. The report shall consist of results of the lotacceptance inspection for the shipment and the results of the most recent periodic-check astmm. The following pieces are to be used for the listed relevant test methods: It is possible, by agreement between the buyer and the seller, that materials incorporating other pigments or soluble stabilizers, or both, may prove adequate for particular applications.

The melting point, Tm, is obtained from the second melting curve.