2SK datasheet, 2SK circuit, 2SK data sheet: UTC – HIGH FREQUENCY AMPLIFIER N-CHANNEL SILICON JUNCTION FIELD EFFECT. 2SK Datasheet PDF Download – HIGH FREQUENCY AMPLIFIER -CHANNEL SILICON JUNCTION FIELD EFFECT TRANSISTOR, 2SK data sheet. 2SKLK53 from NEC Corporation. Find the PDF Datasheet, Specifications and Distributor Information.

Author: Arara Totaxe
Country: Spain
Language: English (Spanish)
Genre: Spiritual
Published (Last): 19 August 2007
Pages: 146
PDF File Size: 2.79 Mb
ePub File Size: 10.42 Mb
ISBN: 724-1-27258-458-6
Downloads: 37644
Price: Free* [*Free Regsitration Required]
Uploader: Tudal

That seems like the most sensible way of performing the adjustment, given that we want the best possible real-life AGC performance.

The receiver features no less than four front ends: And in fact, I think that much improved 2sk5088 accuracy and improved stability were the main reasons for choosing this concept over a classic single conversion one, along with better image and spurious rejection.

There is a screw between the lower edge of the board and the battery compartment to be 2ks508. These days, this receiver concept really is something for weaker signal areas only, and I would therefore hesitate to recommend buying a new receiver using it they typically do seem to have fairly good selectivity though.

I guess this set was supposed to mimic an analog not only in look and feel but also in power consumption, being geared more towards the traveler rather than the shortwave enthusiast who’d obviously prefer the ‘DS by quite a margin. I have mentioned a local one in the misc links section.

I bought a used ICF in Should you experience audio distortion in the AM mode only, particularly with bass-heavy content, the AGC adjustment needs to be carried out. It has worked like new ever since.

The Sony series page: ICF, ICFDA/

Now to the most interesting part, the shortwave bands, where the receiver works with dual conversion: Incidentally, the venerable ICFW isn’t a Wadley receiver either, just an almost “normal” dual conversion rx with a tuned front-end and bipolar balanced mixer, btw that reuses some FM IF filters for the 1st SW IF, with a crystal-based marker frequency generator kHz and a slightly and precisely adjustable 2nd LO frequency thrown in.

Not that much of a battery hog. Head over to my receiver review corner in order to read it. This, BTW, uses a 2SKY FET and a variable mixing frequency that’s what you vary with the main tuning knob — a “digital”, by contrast, has a constant 2nd mixing frequency since the frequency variation part already took place one IF earlier. I did this for inspection purposes, and when I had located RV2, I plugged it back in, and was able to operate the set with the board raised, so I could adjust RV2.

Here’s a complete scanned service manual for the ICF Sony chose the 1st IF of ICF Additional information Servicing and internals. It had apparently been someone’s workshop radio, judging from the huge amounts of brownish dust inside and several paint sprinkles outside. If you want to go further, unplug the ribbon cable and fold the board back.


2SK508 Datasheet PDF – Unisonic Technologies

The trick when tuning the rx is finding a marker het close to the desired frequency. This is done by adjusting RV2 2sk50 trim pot near the upper right corner of the main PCB’s component side so that a voltage of 1. The critical part in terms of drift remains the 1st LO.

Sounds easy — however, fairly comprehensive disassembly will be required to get to this point, which is not entirely trivial see the next section as 2dk508 as the linked Japanese page.

I did not get a VM accurate to 3 or 4 decimal places to adjust it, I just tuned a strong local AM mw music station, Listened on a set of High-Fi earphones with good bass response, and adjusted it for least distortion.

Combining a wideband frontend with an unbalanced first mixer — as found in these inexpensive sets — is not a very smart thing to do, as 2nd order intermod quickly becomes a major problem. The interesting part is that if you can’t find a datasheet for one version, one that covers another version generelly will also do plus you can still buy at least the current iteration of such a chip in case a replacement is needed.

After having studied the service manual of the ICF LI’d summarize the architecture of the set as follows:. Looking at the circuitry, I would agree with the assessment of adequate, but not outstanding shortwave performance. I conducted a head-to-head comparison with my trusty SWG both just on the whipwhich resulted in my first ever “official” radio review. Suck the solder out of the hole for the ground wire that joins the 2 boards with a pump or wicking.

It’s not in the way of anything. In this form, it cannot reach the same raw reception performance as a “normal” dual conversion concept; this would have required both a tracking filter on the 1st IF and a beefier 2nd mixer.

I bought this set NEW from a Sony dealer inhave forgotten which year. While it is remotely related to the well-known triple conversion Wadley Loop concept in that it uses a fairly wideband IF stage the first IF in this case and consequently has similar issues with strong signal handling if the 2nd mixer isn’t pretty good, it actually bears a lot more resemblance to another s concept, namely the Collins 51J-4’s for bands If you need a service manual in paper form, there are various sources that sell ’em.

Now, find the molded-in plastic hooks that hold the board in place, and release the board and lift it up. While being quite ingenious when originally thought up aroundit already was outdated by the time the ICF came out and inexpensive frequency counters would have allowed a conventional dual conversion design with ultimately better reception and readout accuracy if not the same stability, always a problem with wide-range analog tuned oscillators.


The “digitals”, by comparison, vary this 1st mixing frequency and thus can employ narrow crystal filters in the 1st IF to reduce IM3 by the 2nd mixer — but they don’t have to fear frequency instability as much as analogs. While the differences between various international versions were generally pretty much restricted to FM coverage starting at either 76 or The resulting versions are:.

The “about” part is because the mixer takes its constant mixing frequency from a crystal oscillator with switched crystals of There is no mechanical reason to remove the speaker from the case. The original service manual bears a coppyright date of Partly but not solely due to all the different versions, the service docs are pretty thick, in stark contrast to the ‘s minimal service manual! The first one in particular was not minor, indicating that several bugs had to be worked out.

The 2nd mixer in the older set is less prone to overload as well. This had me puzzled for a while.

2SK Datasheet PDF – NEC

It will seem that Sony likes to refresh existing IC designs once in a while, replacing older ICs with new functionally identical ones, probably to accomodate for changed production processes. It has always worked well until the last year or so, when the distortion on AM started to creep in, and finally got bad enough to make me get in to it. If you want to operate the set out of the case, substitute another speaker, or use extension leads to the one in the case.

While this is of adequate quality, my own scan of the regular non-L ICF’s schematic is somewhat better still: In case you are wondering where the second AGC line used for post-preamp AGC went in post samples unlike its predecessor circuit, the opamp based AGC amp has only one outputlook at the first correction from supplement-1 — the main board schematic from the original service manual does not fully cover the changes.

The ribbon cable connector on the board should be a datashfet locking piece that releases the cable when the upper part is pushed upwards, similar to what the SW datashewt. The shifted 75m coverage also means that the respective input tank circuit is peaked at instead of kHz, which does not make all that much sense given that actual stations are typically found between about to kHz.

I forget if the plastic hook catches need to be pressed in, or pried out, but the back cover came off without a fight.